Pfister E23-BMFC Manual do Utilizador Página 3

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 8
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 2
8 DRAIN POP-UP INSTALLATION
Remove Stoper (8A) and apply Plumbers Patty to underside of Flange
(8D) and to all treads. Insert Drain Body (8B)andWasher(8C) through
Bidet Hole (8E).Fromunderneiththebidet,placeWasher(8F) on
the bottom of the Bidet Hole (8E) and thread the Lower Body (8G)
securely into the Drain Body (8B). Do not over tighten and make sure
that the Ball Rod Opening (8H) is facing the back of the bidet. Insert
Stoper (8A) though the Drain Body opening.
9 POP-UP ROD ADJUSTMENT
Insert the Ball Rod (9A)andBallWasher(9B) into the Ball Rod Opening
(9C). Place the Clamp Nut (9D) in the Ball Rod (9A) and tighten securely
to the Ball Rod Opening (9C).WithLiftRod(9E) in position on the faucet,
insert Lift Rod Strap (9F) and retain it with Thumb Screw (9G). Insert
one hole from the Spring Clip (9H) into the Ball Rod (9A). Guide the
Ball Rod (9A) one of the holes in the Lift Strap (9J) and secure it with
the second hole in the Spring Clip (9H).AdjusttheheightoftheLiftRod
(9E) by loosening up the Thunb Screw (9G) and reseting it tightly.
CAUTION: Maintenance
DISASSEMBLY
♦Replacement parts may be available at thestore where you
purchased your faucet.
♦Pleasecontact your localdistributor for replacement partsif
needed.
♦Always turn off water and relieve pressure before working
on your faucet.
NOTE: Trim Care
Cleaning Instructions:
For all Handles and decorative finishes, use only a soft cloth dampened
with plain water to clean and shine. Use of polish, detergents, abrasive
cleaners, organic solvents or acid may cause damage. Use of other
than a soft damp cloth will nullify our warranty!
Special Trim: Trim products which contain Porcelain or other similar
substance are not acceptable for public areas or Commercial use.
Installation of Said Trim is at Users Risk!
9
11
11 FLUSHING & AERATOR CLEANING
Afterinstallationiscomplete,removeAerator(11A) from Spout (11B).
Turnwatersupplyvalvesonandturnfauceton.Allowbothhotandcold
water to run at least one minute each until all foreign matter has cleared
theline..Whilewaterisrunning,checkforleaks.Tocleanaeratorlift
out Insert (11C) and screen (11D) from aerator Basket (11E). Rinse
parts and replace.
8
Any questions or concerns on Price
Pster products, contact your local Price
Pster distributor or point of contact.
10 FAUCET START UP
Turn on hot and cold water supplies, and check for leaks above and
below the sink
10
3
ENGLISH
11B
11A
11C
11D
11E
8A
8C
10B
8D
8E
8F
8G
8H
9C
9A
9F
9B
9H
9G
9E
9D
9J
9D
9A
9J
9G
9E
Vista de página 2
1 2 3 4 5 6 7 8

Comentários a estes Manuais

Sem comentários